Choke & Kill Manifolds

Choke and kill mainfolds are important well control equipments in balancing pressure in near – balanced drilling wells during petroleum exploration. Choke manifold controls the casing pressure and maintains the balance inside the well, the soft closing of the well is realized by relieving pressure and maintains the balance inside the well, the soft closing of the well is realized by relieving pressure through the choke valve, through which the casing pressure can directly blow out in order to protect the well. Various kinds of valves are made of high – quality materials. The valve torpue of switch is small. It has good sealing, safe and reliable and products meet the standards requesting of API Spec and 16C. There are three pressure grades for the manifold made in our company: 35MPa/70MPa/105MPa.

There are different models of choke manifold for sale from R&T Group, they are JG103/103-105, JG103/103-70, JG103/103-35, JG103/78-105, JG103/78-70, JG103/80-35. 

Different models of choke manifolds are differs from these factors:
rated working pressure（MPa）
main bore valve model and quantity
bypass valve model and quantity
hydraulic choke valve
pressure choke manifold dimension





Comments

Post a Comment

Popular posts from this blog

The wellhead installation standardization process

Image
13-3/8 "casing head installation 1. 17-1/2 "drill bit drilling into the design well, pulling out the drilling tool, and then entering 13-3/8" surface casing to predetermined position, cementing. 2. Cut the 20 "catheter, then lift the upper portion of the catheter, with a height difference of 510mm from the 20" catheter, and the line with a rough cut of 13-3/8 ". 3. Remove the broken casing. 4. After measuring the height of the catheter, it should be cut with the height difference of 505mm from the catheter, and then cut 13-3/8 ". 5. Check the original horizontal condition of 13-3/8 with the horizontal ruler, if not, cut the higher part to the level. 6. Use gas cutting method to cut out the - end of the 3/8 "casing preliminary groove, groove in the wheel again into a 10 * 30 °, and asking for groove edges and a smooth feel. 7. The sealing parts of the surface outside casing string and with emery cloth "BT" seal ring wil...
Read more

R&T Tubing head series products

Image
The tubing head is a device or nipple with flanges at both ends. Before perforating, install it on top of the top casing head. To support the tubing, and seal the annulus space between the tubing and the production casing. It also provides an entrance to the casing and tubing ring space through the side outlet. all types of tubing head Function of tubing head. Suspension well tubing string. The annular space between the sealing tubing and the casing. Provide a transition connection for the casing head and the tree. The two sides of the tubing head can be used for water injection and well washing. The structure of the tubing head. The tubing head consists of tubing head, tubing hanger, sealing device, top wire, gate valve, pressure gauge and flange. The top of the tubing is connected to the tree by a flanged flanged flange. The form of the connection is flanged and clamped. 1). Tubing hanger The tubing hanger is a device that sits in the cone...
Read more

Fault check and maintenance of special tubing head spool and casing head joint

Image
Casing hanger also has a main seal and seal design, the main casing hangers types are rubber seal and seal USES is square type "O" ring seal in the form of combination of vice seal is to use "BT" sealing ring and sealing grease (PTFE) was injected through the seal. 1. Seal ring leakage of two flange joints. If leakage occurs in the sealing gasket ring of the two flange joints, the main seal or secondary seal of the casing hanger has been leaked, and it may be that both the main seal and the secondary seal are leaking. The cause of the main seal leakage is square seal is damaged or heat expansion will casing pipe hanger upward lift, causing party type sealing ring seal effect, so should pay special attention to when the casing hanger, square seal damage can not be cut. The reason for the secondary seal leakage is that the "BT" sealing ring cannot be sealed. (PTFE should be injected into the "BT" sealing ring after the tubing head is connecte...
Read more